Retail Floor Coatings in Cherry Hill, NJ
Jersey Epoxy installs seamless, slip-safe retail floor coatings across Cherry Hill, NJ, a high-build epoxy or resinous finish that holds an even surface under all-day foot traffic, carts, and tracked-in grit. We diamond-grind the slab, repair cracks, and confirm it is dry and sound before we coat, then phase the work overnight so your doors open on schedule. Free on-site quotes.
- Diamond-ground prep
- Serving Camden County
- 20+ years installing
- Free on-site quotes
- Diamond-Ground Prep
- Profiled, dry, and sound first
- Homes & Businesses
- Residential and commercial systems
- 20+ Years Experience
- Floor coatings across NJ & eastern PA
- Free On-Site Survey
- A written spec and a firm number
Cherry Hill up close
What a Cherry Hill retail floor is up against
Retail floors fail first in the traffic lanes, where feet and cart wheels follow the same path from the door to the register all day. We install seamless high-build epoxy abrasion-rated for the actual cart and foot-traffic count, then broadcast anti-slip aggregate into the entry, where a wet day turns the walk-off zone into a fall hazard. A storefront along the Route 70 and Route 38 corridor or near the Cherry Hill Mall takes constant public traffic plus the rain, snow, and road salt tracked in at the door through 30 to 40 freeze-thaw cycles a winter, and a thin coating grinds dull right in those lanes. A system spec'd to the load wears evenly instead.
Receiving and stockrooms behind the sales floor carry pallet-jack and cart loads, so those zones get a forklift-rated epoxy build. Before any of it goes down we diamond-grind the slab to a clean bond, repair cracks, and make sure the concrete is dry and sound, because moisture pushing up through a slab is the top cause of coating failure. We pour overnight and use fast-cure systems where an area has to reopen by morning, so a floor job in Cherry Hill does not cost you selling days.
Our approach
How we build retail floor coatings in Cherry Hill
No single approach fits every retail floor. Here is what goes into a retail floor coatings that lasts in Cherry Hill.
Why prep wins
A Cherry Hill retail floor lasts or fails before the first coat
Most retail floor coatings that fail were not beaten by the wrong product. They were rolled over a dusty or damp slab the coating could never bond to. For a retail floor in Cherry Hill, we diamond-grind to a clean profile, repair the cracks and pitting, and make sure the slab is dry and sound before anything goes down.
From there we match the system to the retail floor: Epoxy Flooring or Polished Concrete, specified for what this floor actually has to take. The prep is the same rigor every time; the system follows the job.
- Diamond-ground to a clean profile so the coating keys into sound concrete, not a dusty top layer. [ICRI CSP]
- Cracks and pitting repaired and joints honored, so the finish does not telegraph the slab beneath it.
- Dry, sound slab first, the top cause of coating failure, so a moisture test is worth doing where the water table runs high.
- System matched to the retail floor, not one coating used everywhere.
How it works
From your first call to the final coat
We map the whole job before we touch the floor, then phase the work around your production.
- Free Quote(877) 376-9965No-cost on-site assessmentGet my quote
Call or Contact Us
Tell us about the space and your timeline.
- Walk-through
- Grind & repair
- Dry, sound slab
- Epoxy Flooring
On-Site Survey
A free walk-through and a written floor spec.
- Slab PrepProfiledDry & sound
Preparation
Slab diamond-ground and prepped to dry, sound concrete before coating.
- Sealed
Installation
Seamless system installed and sealed.
Standards & specifications
Held to the standards a coating is actually tested against
Every floor answers to load, slip, adhesion, and moisture before it answers to looks. Here is each requirement and the published standard we hold the spec to.
Slab moisture
Older NJ and PA slabs often have no vapor barrier, and vapor pushing up from an unbarriered slab is the leading reason a coating lets go from underneath. The slab has to be dry and sound before we coat, and on a high-water-table or below-grade slab a moisture test (ASTM F2170 or F1869) is worth doing first. [ASTM F2170 / F1869]
Surface profile & adhesion
We diamond-grind the slab to a concrete surface profile that the primer can key into, so the coating bonds to sound concrete rather than to a dusty top layer. Pull-off adhesion is measured to ASTM D7234. [ICRI CSP / ASTM D7234]
Slip resistance (wet)
Anti-slip aggregate broadcast into entries, ramps, and any area that gets wet, dialed toward the ANSI A326.3 wet DCOF benchmark of 0.42. Texture is set area by area, and no wet floor is ever fully slip-proof. [ANSI A326.3]
Compressive & abrasion strength
Industrial epoxies and resinous mortars carry compressive strengths well above plain concrete (ASTM C579) and resist abrasion under Taber testing (ASTM D4060), matched to the traffic the floor actually takes. [ASTM C579 / D4060]
These targets are met by the systems we install and the products we specify into them. Jersey Epoxy is the installer, not a certifying body, so we point to the standard on the spec rather than calling ourselves certified.
What you get
Why Cherry Hill chooses our retail floor coatings
Tough Walk-Off Entry
Anti-slip aggregate at the door, the most abrasive and slippery spot in the building.
Seamless Sales Floor
A high-build floor down the aisles so the busy lanes wear like the rest of the store.
Receiving-Dock Durable
A forklift-rated build for stockrooms and receiving behind the sales floor.
Mops Clean
A non-porous, seamless surface with no grout lines for dirt to collect in.
No Lost Selling Days
We pour overnight and use fast-cure systems so the store reopens by morning.
Recommended system
The systems we use for retail floors
The chemistry we reach for on a Cherry Hill retail floor, and why.
Epoxy Flooring
A hard, high-build base sized to forklift and point loads: the workhorse for warehouse aisles, dock approaches, and shop floors.
Explore system
Polished Concrete
A hard, low-maintenance, light-reflective finish for large retail and warehouse footprints, densifying and sealing the existing slab.
Explore systemProudly Serving New Jersey & Eastern PA
Our crews are on the road daily. Select your region to see our coverage.
New Jersey
Statewide Coverage- Bergen & Essex County
- Monmouth & Ocean County
- Middlesex & Somerset County
- Camden & Burlington County
- Hudson & Morris County
FAQ
Retail Floor Coatings in Cherry Hill, answered
Our Cherry Hill store floor is dull down the checkout lanes but still sharp in the corners. What went wrong?
That is traffic-lane wear. Feet and cart wheels follow the same paths from the door to the register all day, and a thin or poorly bonded coating grinds dull right along those lines while the corners stay new. We grind the slab to a clean profile first, then build a seamless system thick enough and abrasion-rated enough that the busy lanes wear like the rest of the floor.
Can the entry handle the salt and water tracked in all winter?
Yes. The door is the most abrasive and slippery spot in the building, especially along the Route 70 corridor where customers track in rain, snow-melt, and road salt. We broadcast anti-slip aggregate into the walk-off zone for traction and seal it so the salt and water stay on top to be cleaned up instead of soaking into the slab.
Can you install the floor without closing the store?
Yes. We phase the work and pour overnight around your hours, and use fast-cure systems where an area has to reopen by morning, so a floor job in Cherry Hill does not cost you selling days. We confirm the schedule at the free on-site quote.
Get started
Get a free quote on your Cherry Hill retail floor
We walk the retail floor at no cost, read the slab, and come back with a written spec and a firm number for your Cherry Hill retail floor coatings.
(877) 376-9965 · talk to an installerRated 5 stars by New Jersey homeowners & businesses
Powered by Google
No Obligation
