Restaurant Floor Coatings in Cherry Hill, NJ
Jersey Epoxy installs restaurant floor coatings across Cherry Hill, NJ, seamless resinous systems for the kitchen and dish pit plus decorative finishes for the dining room. We build slip resistance into the wet, greasy zones, cove the floor up the wall for food-code cleaning, diamond-grind the slab, and repair cracks before we coat, working off-hours so you never lose a service. Free on-site quotes.
- Diamond-ground prep
- Serving Camden County
- 20+ years installing
- Free on-site quotes
- Diamond-Ground Prep
- Profiled, dry, and sound first
- Homes & Businesses
- Residential and commercial systems
- 20+ Years Experience
- Floor coatings across NJ & eastern PA
- Free On-Site Survey
- A written spec and a firm number
Cherry Hill up close
What a Cherry Hill restaurant floor is up against
The Route 70 and Route 38 corridor and the Cherry Hill Mall area are full of restaurants and commercial kitchens, and a working kitchen runs grease, hot washdown water, and twice-daily scrub-downs over the same slab. Tile grout lines trap all of it, which is why we finish back-of-house zones in seamless resinous flooring with anti-slip aggregate broadcast into the surface, and detail a radius cove where the floor meets the wall so grease and debris have no square corner to collect in. The result is a sanitary, washdown-rated surface that hides nothing in a grout line and holds traction where water hits the floor.
Before any finish goes down we diamond-grind the slab to a clean profile and repair cracks, because the concrete has to be dry and sound to hold a kitchen coating. The dining room gets a clean, durable finish that takes constant foot traffic, so the floor reads as one building front to back. We phase the work overnight or across a weekend so the business never closes.
Our approach
How we build restaurant floor coatings in Cherry Hill
No single approach fits every restaurant floor. Here is what goes into a restaurant floor coatings that lasts in Cherry Hill.
Why prep wins
A Cherry Hill restaurant floor lasts or fails before the first coat
Most restaurant floor coatings that fail were not beaten by the wrong product. They were rolled over a dusty or damp slab the coating could never bond to. For a restaurant floor in Cherry Hill, we diamond-grind to a clean profile, repair the cracks and pitting, and make sure the slab is dry and sound before anything goes down.
From there we match the system to the restaurant floor: Resinous Flooring or Epoxy Flooring, specified for what this floor actually has to take. The prep is the same rigor every time; the system follows the job.
- Diamond-ground to a clean profile so the coating keys into sound concrete, not a dusty top layer. [ICRI CSP]
- Cracks and pitting repaired and joints honored, so the finish does not telegraph the slab beneath it.
- Dry, sound slab first, the top cause of coating failure, so a moisture test is worth doing where the water table runs high.
- System matched to the restaurant floor, not one coating used everywhere.
How it works
From your first call to the final coat
We map the whole job before we touch the floor, then phase the work around your production.
- Free Quote(877) 376-9965No-cost on-site assessmentGet my quote
Call or Contact Us
Tell us about the space and your timeline.
- Walk-through
- Grind & repair
- Dry, sound slab
- Resinous Flooring
On-Site Survey
A free walk-through and a written floor spec.
- Slab PrepProfiledDry & sound
Preparation
Slab diamond-ground and prepped to dry, sound concrete before coating.
- Sealed
Installation
Seamless system installed and sealed.
Standards & specifications
Held to the standards a coating is actually tested against
Every floor answers to load, slip, adhesion, and moisture before it answers to looks. Here is each requirement and the published standard we hold the spec to.
Slab moisture
Older NJ and PA slabs often have no vapor barrier, and vapor pushing up from an unbarriered slab is the leading reason a coating lets go from underneath. The slab has to be dry and sound before we coat, and on a high-water-table or below-grade slab a moisture test (ASTM F2170 or F1869) is worth doing first. [ASTM F2170 / F1869]
Surface profile & adhesion
We diamond-grind the slab to a concrete surface profile that the primer can key into, so the coating bonds to sound concrete rather than to a dusty top layer. Pull-off adhesion is measured to ASTM D7234. [ICRI CSP / ASTM D7234]
Slip resistance (wet)
Anti-slip aggregate broadcast into entries, ramps, and any area that gets wet, dialed toward the ANSI A326.3 wet DCOF benchmark of 0.42. Texture is set area by area, and no wet floor is ever fully slip-proof. [ANSI A326.3]
Compressive & abrasion strength
Industrial epoxies and resinous mortars carry compressive strengths well above plain concrete (ASTM C579) and resist abrasion under Taber testing (ASTM D4060), matched to the traffic the floor actually takes. [ASTM C579 / D4060]
These targets are met by the systems we install and the products we specify into them. Jersey Epoxy is the installer, not a certifying body, so we point to the standard on the spec rather than calling ourselves certified.
What you get
Why Cherry Hill chooses our restaurant floor coatings
Sanitary Kitchen Floors
Seamless, washdown-rated resinous with a coved base for the back of house.
Grease & Acid Resistant
Stands up to grease, food acids, and hot spills without staining or pitting.
Slip-Rated
Anti-slip texture where the floor gets wet, tuned to the ANSI A326.3 wet benchmark.
Durable Front-of-House
A clean, durable finish for the dining room that takes constant foot traffic.
Installed Around Service
We work overnight so you do not lose a single service.
Recommended system
The systems we use for restaurant floors
The chemistry we reach for on a Cherry Hill restaurant floor, and why.
Resinous Flooring
Seamless, chemical-resistant, and non-porous: it takes a daily washdown and shrugs off oils and spills in kitchens and food spaces.
Explore system
Epoxy Flooring
A hard, high-build base sized to forklift and point loads: the workhorse for warehouse aisles, dock approaches, and shop floors.
Explore systemProudly Serving New Jersey & Eastern PA
Our crews are on the road daily. Select your region to see our coverage.
New Jersey
Statewide Coverage- Bergen & Essex County
- Monmouth & Ocean County
- Middlesex & Somerset County
- Camden & Burlington County
- Hudson & Morris County
FAQ
Restaurant Floor Coatings in Cherry Hill, answered
Can you coat the kitchen and the dining room with one company?
Yes. In Cherry Hill we spec the back of house for grease and sanitation with seamless resinous systems and a coved base, and finish the dining room and bar in a durable decorative finish, then install both as one job so the floor reads as one building front to back.
How do you keep a Cherry Hill kitchen floor from turning slick once grease and washdown water hit it?
Wet plus grease is the worst slip case in any restaurant, so we broadcast anti-slip aggregate into the kitchen, dish pit, and prep line to build traction underfoot, and step the texture up around the grill and fryers. No wet floor is ever fully slip-proof, and we say so up front.
Can you install without closing my restaurant on the Route 70 corridor?
Yes. We phase the work overnight or across a weekend so you do not lose a service, and use fast-cure systems where a zone has to reopen by the next service. We confirm the schedule and the slab condition at the free on-site quote.
Get started
Get a free quote on your Cherry Hill restaurant floor
We walk the restaurant floor at no cost, read the slab, and come back with a written spec and a firm number for your Cherry Hill restaurant floor coatings.
(877) 376-9965 · talk to an installerRated 5 stars by New Jersey homeowners & businesses
Powered by Google
No Obligation
