Epoxy Flooring in Franklin Lakes, NJ
Jersey Epoxy installs garage, finished-basement, and pool-deck floor coatings in Franklin Lakes. We diamond-grind every slab and make sure it is dry and sound, then seal it with a flake, polyaspartic, or metallic system built to take Bergen County road salt, freeze-thaw winters, and humid summers. Free on-site quotes.
- Diamond-ground prep
- Serving Bergen County
- 20+ years installing
- Free on-site quotes
- Diamond-Ground Prep
- Profiled, dry, and sound first
- Homes & Businesses
- Residential and commercial systems
- 20+ Years Experience
- Floor coatings across NJ & eastern PA
- Free On-Site Survey
- A written spec and a firm number
Franklin Lakes up close
What a Franklin Lakes floor is really up against
Garage floors are the most common job in Franklin Lakes. All winter, cars track road salt and snowmelt in off Route 208 and Franklin Avenue, and Bergen County runs a hard freeze-thaw cycle, so a bare or painted garage slab spalls and cracks at the joints. We grind the slab to a clean profile, repair it, and seal it with a flake or polyaspartic floor and a hot-tire-resistant topcoat that keeps salt and warm tires off the concrete.
Finished basements take a metallic or solid-color epoxy floor over a moisture-tolerant build, and we make sure the slab is dry first because a humid summer pushes vapor up through an unsealed slab. Pool decks and patios get a UV-stable, slip-resistant coating that handles sun, water, and freeze-thaw.
Zone-by-zone
We spec each area of the building for the job it actually does
No single coating is right everywhere. Here is how we read a floor and match the chemistry to the punishment.
Why prep wins
The floor lasts or fails on what happens before the first coat
Most failed floors in New Jersey were not beaten by the wrong resin. They were rolled over a dusty or damp slab that the coating could never bond to. We diamond-grind every floor to a clean profile, repair the cracks and pitting, and make sure the slab is dry and sound before anything goes down.
From there the system is matched to the room: a hard-wearing flake or polyaspartic build for a garage that sees tires and salt, a moisture-tolerant epoxy for a basement, a decorative metallic for a finished living space. The prep is the same rigor every time; the system changes with the job.
- Diamond-ground to profile so the primer keys into sound concrete, not a dusty top layer. [ICRI CSP]
- Dry, sound slab before the first coat, the single most common cause of early delamination, so a moisture test is worth doing where the slab could be wet. [ASTM F2170]
- Cracks and pitting repaired and joints honored, so the finish does not telegraph the slab beneath it.
- System matched to the load, from flake garages to forklift-rated warehouse floors, instead of one coating everywhere.
How it works
From your first call to the final coat
We map the whole job before we touch the floor, then phase the work around your production.
- Free Quote(877) 376-9965No-cost on-site assessmentGet my quote
Call or Contact Us
Tell us about the space and your timeline.
- Walk-through
- Garages
- Basements
- Commercial
On-Site Survey
A free walk-through and a written floor spec.
- Slab PrepProfiledDry & sound
Preparation
Slab diamond-ground and prepped to dry, sound concrete before coating.
- Sealed
Installation
Seamless system installed and sealed.
Standards & specifications
Held to the standards a coating is actually tested against
Every floor answers to load, slip, adhesion, and moisture before it answers to looks. Here is each requirement and the published standard we hold the spec to.
Slab moisture
Older NJ and PA slabs often have no vapor barrier, and vapor pushing up from an unbarriered slab is the leading reason a coating lets go from underneath. The slab has to be dry and sound before we coat, and on a high-water-table or below-grade slab a moisture test (ASTM F2170 or F1869) is worth doing first. [ASTM F2170 / F1869]
Surface profile & adhesion
We diamond-grind the slab to a concrete surface profile that the primer can key into, so the coating bonds to sound concrete rather than to a dusty top layer. Pull-off adhesion is measured to ASTM D7234. [ICRI CSP / ASTM D7234]
Slip resistance (wet)
Anti-slip aggregate broadcast into entries, ramps, and any area that gets wet, dialed toward the ANSI A326.3 wet DCOF benchmark of 0.42. Texture is set area by area, and no wet floor is ever fully slip-proof. [ANSI A326.3]
Compressive & abrasion strength
Industrial epoxies and resinous mortars carry compressive strengths well above plain concrete (ASTM C579) and resist abrasion under Taber testing (ASTM D4060), matched to the traffic the floor actually takes. [ASTM C579 / D4060]
These targets are met by the systems we install and the products we specify into them. Jersey Epoxy is the installer, not a certifying body, so we point to the standard on the spec rather than calling ourselves certified.
What you get
A floor in Franklin Lakes that holds up to the work and the weather
Residential: Garage floors in flake and polyaspartic, metallic and solid-color floors for finished basements, and UV-stable coatings for pool decks and patios. Commercial: Office and retail floors along the Franklin Avenue corridor, on the same prep-first standard.
Built for NJ & PA Winters
Sealed against road salt and moisture and able to ride 30 to 40 freeze-thaw swings a year without lifting at the joints.
Diamond-Ground, Not Rolled Over
We profile and repair the slab and make sure it is dry first, the step most one-day coaters skip and the reason their floors peel.
One Crew, Homes and Businesses
The same crew that coats a garage handles warehouse, kitchen, and retail floors, phased around your hours.
Cleanable & Slip-Rated
A seamless, non-porous surface that sweeps and mops clean, with anti-slip texture dialed in where floors get wet.
Fast Return to Service
Polyaspartic options let a garage or a bay come back the same day instead of waiting out a multi-day cure.
A Real, Written Quote
A free on-site survey and a written, firm number for your specific floor before any work starts.
Recommended systems
The coatings we install most
The systems that carry most residential jobs, with the chemistry behind each.
Flake Epoxy
A broadcast vinyl-flake floor with a tough topcoat: the go-to for garages and basements, hard-wearing and easy to clean.
Explore systemMetallic Epoxy
A seamless, one-of-a-kind marbled finish for interiors and finished basements where the floor is part of the room.
Explore system
Polyaspartic
A fast-cure, UV-stable topcoat that installs in cold weather and returns to service in a day. Strong over garages and exterior slabs.
Explore systemProudly Serving New Jersey & Eastern PA
Our crews are on the road daily. Select your region to see our coverage.
New Jersey
Statewide Coverage- Bergen & Essex County
- Monmouth & Ocean County
- Middlesex & Somerset County
- Camden & Burlington County
- Hudson & Morris County
FAQ
Epoxy flooring in Franklin Lakes, answered straight
Will an epoxy garage floor hold up to the road salt and freeze-thaw here?
Yes, when the slab is ground and sealed first. Road salt soaking into bare concrete plus freeze-thaw is what spalls an unsealed floor. A flake or polyaspartic system seals the slab, and the hard topcoat resists hot-tire pickup.
Can you do a finished-basement floor in metallic or a solid color?
Yes. We install metallic and solid-color epoxy floors over a moisture-tolerant build, and we make sure the slab is dry first so a humid summer does not push the floor loose. We bring samples to the quote.
Do you coat pool decks and patios?
Yes. Pool decks and patios get a UV-stable, slip-resistant coating built to take sun, water, and freeze-thaw.
Which Bergen County towns do you serve?
Franklin Lakes, Wyckoff, Oakland, Ridgewood, Mahwah, Ramsey, and Saddle River across Bergen County.
Get started
Let us spec a floor for your Franklin Lakes project
We walk the space at no cost, read the slab, and come back with a written spec and a firm number.
(877) 376-9965 · talk to an installerRated 5 stars by New Jersey homeowners & businesses
Powered by Google
No Obligation
