Patio Epoxy Coating in Lakewood, NJ
Jersey Epoxy installs UV-stable polyaspartic patio coatings across Lakewood. On a Lakewood backyard patio that bakes in open Ocean County sun, this finish stays slip-resistant, keeps its color, and lets the family back outside within a day. We diamond-grind the slab, repair cracks, and make sure the concrete is dry and sound before we coat. Free on-site quotes.
- Diamond-ground prep
- Serving Ocean County
- 20+ years installing
- Free on-site quotes
- Diamond-Ground Prep
- Profiled, dry, and sound first
- Homes & Businesses
- Residential and commercial systems
- 20+ Years Experience
- Floor coatings across NJ & eastern PA
- Free On-Site Survey
- A written spec and a firm number
Lakewood up close
What a Lakewood patio is up against
We finish exterior patios in Lakewood with polyaspartic rather than standard epoxy, because a patio lives in open sun and standard epoxy ambers and chalks under UV. Polyaspartic holds its color, cures fast, and stays flexible as the slab moves through 30 to 40 freeze-thaw cycles a winter. That matters on the larger family homes near Cedarbridge Avenue and New Hampshire Avenue, where a patio takes full sun through the summer and road salt tracked across it all winter.
On a slab this close to grade, moisture pushing up through the concrete is the real threat to a patio coating, so we make sure the slab is dry and sound before it takes a finish. Where drainage is poor or a slab sits low, a moisture test is worth doing first. We diamond-grind the patio to a clean profile and repair cracks before any coating goes down, which is what keeps the polyaspartic bonded through humid Ocean County summers.
Our approach
How we build patio epoxy coating in Lakewood
No single approach fits every patio. Here is what goes into a patio epoxy coating that lasts in Lakewood.
Why prep wins
A Lakewood patio lasts or fails before the first coat
Most patio coatings that fail were not beaten by the wrong product. They were rolled over a dusty or damp slab the coating could never bond to. For a patio in Lakewood, we diamond-grind to a clean profile, repair the cracks and pitting, and make sure the slab is dry and sound before anything goes down.
From there we match the system to the patio: Polyaspartic, specified for what this floor actually has to take. The prep is the same rigor every time; the system follows the job.
- Diamond-ground to a clean profile so the coating keys into sound concrete, not a dusty top layer. [ICRI CSP]
- Cracks and pitting repaired and joints honored, so the finish does not telegraph the slab beneath it.
- Dry, sound slab first, the top cause of coating failure, so a moisture test is worth doing where the water table runs high.
- System matched to the patio, not one coating used everywhere.
How it works
From your first call to the final coat
We map the whole job before we touch the floor, then phase the work around your production.
- Free Quote(877) 376-9965No-cost on-site assessmentGet my quote
Call or Contact Us
Tell us about the space and your timeline.
- Walk-through
- Grind & repair
- Dry, sound slab
- Polyaspartic
On-Site Survey
A free walk-through and a written floor spec.
- Slab PrepProfiledDry & sound
Preparation
Slab diamond-ground and prepped to dry, sound concrete before coating.
- Sealed
Installation
Seamless system installed and sealed.
Standards & specifications
Held to the standards a coating is actually tested against
Every floor answers to load, slip, adhesion, and moisture before it answers to looks. Here is each requirement and the published standard we hold the spec to.
Slab moisture
Older NJ and PA slabs often have no vapor barrier, and vapor pushing up from an unbarriered slab is the leading reason a coating lets go from underneath. The slab has to be dry and sound before we coat, and on a high-water-table or below-grade slab a moisture test (ASTM F2170 or F1869) is worth doing first. [ASTM F2170 / F1869]
Surface profile & adhesion
We diamond-grind the slab to a concrete surface profile that the primer can key into, so the coating bonds to sound concrete rather than to a dusty top layer. Pull-off adhesion is measured to ASTM D7234. [ICRI CSP / ASTM D7234]
Slip resistance (wet)
Anti-slip aggregate broadcast into entries, ramps, and any area that gets wet, dialed toward the ANSI A326.3 wet DCOF benchmark of 0.42. Texture is set area by area, and no wet floor is ever fully slip-proof. [ANSI A326.3]
Compressive & abrasion strength
Industrial epoxies and resinous mortars carry compressive strengths well above plain concrete (ASTM C579) and resist abrasion under Taber testing (ASTM D4060), matched to the traffic the floor actually takes. [ASTM C579 / D4060]
These targets are met by the systems we install and the products we specify into them. Jersey Epoxy is the installer, not a certifying body, so we point to the standard on the spec rather than calling ourselves certified.
What you get
Why Lakewood chooses our patio epoxy coating
UV-Stable Color
Polyaspartic holds its color in full sun instead of ambering like standard epoxy.
Rides the Freeze-Thaw
A flexible, sealed surface that takes the freeze-thaw without cracking or peeling.
Slip-Resistant
An anti-slip texture worked into the finish for traction when the patio is wet.
Back in Use Fast
A fast-cure system is usually walkable the same evening, so you keep your summer.
Sealed & Easy to Clean
A non-porous surface that resists stains and hoses clean.
Recommended system
The system we use for patios
The chemistry we reach for on a Lakewood patio, and why.
Proudly Serving New Jersey & Eastern PA
Our crews are on the road daily. Select your region to see our coverage.
New Jersey
Statewide Coverage- Bergen & Essex County
- Monmouth & Ocean County
- Middlesex & Somerset County
- Camden & Burlington County
- Hudson & Morris County
FAQ
Patio Epoxy Coating in Lakewood, answered
Why polyaspartic instead of epoxy for a Lakewood patio?
A Lakewood backyard patio sits out in the open with no shade, and standard epoxy turns yellow and powdery once that UV hits it day after day. Polyaspartic is UV-stable, so it holds its color outdoors, and it stays flexible through Lakewood's 30 to 40 freeze-thaw cycles a winter. Because it sets quickly, most patios here are ready to walk on the day after we coat.
What does patio slab prep look like for a Lakewood install?
We diamond-grind the concrete to a clean profile so the coating keys into sound slab instead of a dusty surface, then we repair any cracks. The slab also has to be dry before it takes a finish. Where drainage is poor or a slab sits low, we recommend a moisture test first, since moisture pushing up is the top cause of coating failure.
Do you give free patio quotes in Lakewood?
Yes. We provide free on-site quotes throughout Lakewood and Ocean County. We look at the slab condition, measure the patio, and give you a written spec and a firm number.
Get started
Get a free quote on your Lakewood patio
We walk the patio at no cost, read the slab, and come back with a written spec and a firm number for your Lakewood patio epoxy coating.
(877) 376-9965 · talk to an installerRated 5 stars by New Jersey homeowners & businesses
Powered by Google
No Obligation
